Leading 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.
Leading 10 usual forklift crashes ， forklift procedure need to take notice of these issues ！.
Blog Article
Don't ignore the forklift at the office. If the operation is not good, there will be severe crashes in mins, and there are several crashes entailing forklifts.
Case 1: The forklift cargo obstructed the driver's sight, and the person in front could not be located, causing a moving crash.
Instance 2: In order to keep the equilibrium of the forklift when lifting heavy goods, the employees used their body weight as the weight, which virtually created casualties.
Instance 3: The size of the forklift cargo exceeds the allowable size of the course and holds on the roadside shelf, which almost creates an crash.
Situation 4: Forklift is speeding and rolls over throughout a turn.
Situation 5: The forklift motorist did not discover the pedestrian, and the pedestrian did not notice the forklift.
Case 6: The forklift raises the employees illegally, the forklift driver does not put on the safety belt, the forklift lifter falls and the driver is squashed when the forklift rolls over.
Case 7: The forklift vehicle driver did not use a seat belt and dropped from the car when it rolled over and was squashed.
Forklift operation need to take notice of these issues ：.
Start.
1. Prior to starting, observe the environments, and after verifying that there are no obstacles that prevent the security of driving, beep the horn first and then begin.
2. For vehicles with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge need to be safe prior to starting.
3. When the forklift begins with a load, the motorist should first validate that the tons is secure and trustworthy.
4. The start needs to be slow-moving and constant.
Driving.
1. When driving, the height in between the bottom end of the fork and the ground should be kept at 300mm-400mm, and the pole must be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the job site or while driving, take care that there will be no challenges overhead. When the load is traveling, the fork needs to not be elevated too high, which will certainly influence the stability of the forklift. .
3. After discharging, the fork must be decreased to the normal driving setting prior to driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal must be released initially. High-speed sharp turns are restricted. High-speed doglegs will certainly create the vehicle to lose lateral stability and tip over. .
5. When the forklift is downhill, it is purely restricted to switch off the flame and slide, and it is forbidden to brake instantly while driving with loads unless there are special scenarios.
6. When the forklift is running, it should follow the website traffic rules in the manufacturing facility and must keep a certain safety distance from the car in front. .
7. When the forklift is running, the tons needs to remain in the lowest setting that does not impede the driving, and the gantry must be effectively slanted back. The lots will not be increased except when stacking or packing. .
8. The height of the load should not block the chauffeur's sight. In special circumstances, when the item influences the forward vision, drive at a reduced rate when reversing.
9. It is prohibited to turn on the ramp, nor to drive throughout the ramp. .
10. The secure driving speed of the forklift in the factory area is 5 km/h, and it has to drive securely at a low speed when getting in the manufacturing workshop location. .
11. When the forklift is raised, raised or driven, it is forbidden for personnel to depend on the fork to hold things and play a balancing role. .
12. If issues are located, they will certainly be repaired and reported in a prompt way, and they will never ever run with diseases or conceal them.
filling and discharging.
1. When fork-loading items, the range between the two forks need to be changed as needed to make the tons of the two forks well balanced and not skewed, and one side of the item must be against the shelf. .
2. It is prohibited to deal with a solitary fork or utilize a fork top or pull. In unique circumstances, safety and security warning signs have to be set up to advise surrounding pedestrians. .
3. In the process of filling and discharging items, the forklift needs to be braked with the brake. .
4. The speed of the vehicle must be slow and consistent. Be careful not to roll the wheels on the dunnage, so as not to extend the rolled things and harm individuals. .
5. When using a fork to fork the goods, the fork must be as deep as feasible under the tons, and it should be kept in mind that the fork pointer ought to not touch various other goods or items. The lots needs to be supported with minimal back tilt of the gantry to ensure that the load does not move in reverse. The mast can be tilted onward slightly when the tons is decreased to allow for simple positioning of the lots and extraction of the forks. .
6. It is prohibited to fork items at broadband and collide with difficult things with the fork head. .
7. When the forklift is functioning, it is forbidden for people to loaf the fork, so as to prevent the collapse of the goods and harm individuals. .
8. Straining is restricted, and it is forbidden to make use of forks to raise personnel to engage in high-altitude operations to prevent high-altitude dropping crashes. .
9. It is not permitted to make use of the brake inertia to slide, put, round or roll objects. .
10. It is not allowed to use forks to choose, turn pallet discharge.
Leaving .
1. It is prohibited to leave the forklift when the things on the fork impend. Prior to leaving the forklift, you have to dump the goods or reduced the fork framework.
2. Draw the parking brake handle to dead or depress the hand brake button.
3. The engine is switched off and the power is removed. (Except for unique conditions, such as the vehicle driver does not leave the lorry's view and does not go beyond 1 min).
4. Get rid of the secret. .
Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance should be checked, and gas, lubing oil and air conditioning water must be added.
2. Check the safety efficiency of beginning, running and braking.
3. Check whether the lights and horn signals are complete and reliable.
4. During the operation of the forklift, examine whether the stress and temperature are normal.
5. After the forklift is running, the external leak must likewise be checked and the seals need to be changed in time.
Forklift Safety Operation Specifications.
1. You should check prior to leaving the auto;.
2. When you come across somebody Stand-on Electric Pallet Stacker before you throughout driving, you ought to send out a signal at a distance of 5 m;.
3. The driving rate in the factory does not go beyond 5 km/h;.
4. When driving, the low point of the cargo must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop the tendency of "free turning";.
6. Running up and down the incline ought to be slow-moving and uniform, and no activating the slope is allowed.
7. Do not drive throughout the slope. When the gradient is higher than 10%, the vehicle needs to be driven backwards when worsening;.
8. When the forklift personnel lug the goods and move forward, if they run into large or hefty goods and most likely to the driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork procedure is not permitted.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other harmful chemicals with forks.
5. It is not allowed to utilize inertia pressure to grab the goods.
6. It is not allowed to utilize stopping pressure Stand-on Electric Pallet Stacker to exile round or easy-to-roll items.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Auto parking is not allowed under the following conditions.
1. Curves, narrow roadways, train crossings;.
2. Areas with a longitudinal incline greater than 5%.
3. When there is an obstacle on one side of the road, the opposite side of the section with the exact same size as the barrier need to be within 20 meters at each end.
Web：https://www.onenforklifts.com/
Email：info2@onen.cn
Phone：+86 13827083844